Anti Slip Spray for Showers and Bathtubs - Fast Acting Non Slip Coating

Anti Slip Spray for Showers and Bathtubs - Fast Acting Non Slip Coating

Anti Slip Spray works excellent on Fiberglass, Acrylic and most other surfaces. Available in Clear or White. Our non slip spray is the highest rated aerosol spray for fiberglass and acrylic found on the market!.
DESCRIPTION Non-Slip Spray works effectively on Fiberglass, Acrylic and most other surfaces. Available in Clear or White. Our Non-Slip spray is the highest rated aerosol spray for fiberglass/acrylic found on the market! SlipDoctors Non-Slip Spray is an epoxy aerosol that provides a hard, textured finish to help to prevent slip-and-fall accidents. It is barefoot friendly, lead-free, and chemical, gas and oil resistant. It is ideal for both interior and exterior surfaces, it is designed for areas where water is present or slippery conditions exist such as fiberglass and acrylic bathtubs and showers, properly prepared wood, concrete, metal, tile, porcelain/ceramic and many other surfaces. This convenient aerosol spray is the perfect solution to treat small or irregularly shaped surfaces where increased traction is desired. One can covers up to 15 sq. ft. Even when wet, your slippery floor’s slip resistance after the non-slip solution will surpass ANSI A137.1, A326.3 or B101.3 standards. 0.43 Wet DCOF - ANSI B101.30.45 Wet DCOF – ANSI A137.1 / A326.30.65 Wet SCOF - ANSI B101.1 Pendulum Test Values - Slider #55  DRY -96 WET -53 - Slip Risk - LOW Safety Data Sheet (SDS) Technical Data Sheet (TDS) Installation Instructions Testing Document PRODUCT FEATURES Suggested Uses - Fiberglass & Acrylic Bathtubs / Showers- Onyx Shower bases- Kitchens & Bathrooms- Pool Decks, Ladders & Steps- Boats & Trailers- Gyms & Spas- Hotels & Resorts- Residential & Commercial Use SPECIFICATIONS Single Case Coverage per Sq Ft 15 180 Cost per Sq Ft (Appx.) $2.33 $2.13 Note: This item can only ship via ground due to DOT regulations. INSTRUCTIONS EQUIPMENT NEEDED: • One can of SlipDoctors Non-Slip Spray • Painter‘s Tape • Painter’s Paper Note: for porcelain bathtubs, please repair any chips prior to application. Repair kits can be purchased at your local home improvement store SURFACE PREPARATION: Note: we do not recommend using black sandpaper, as it can leave behind small black dots that may be visible after using the clear spray Always test a small area for color compatibility and adhesion. Fiberglass/Acrylic:Lightly sand with 220 grit sand paper to promote adhesion. Clean surface with soap and water or wipe with clean cloth and lacquer thinner (or another cleaner that does not leave a lm or residue) to remove all sanding dust. Allow to dry thoroughly. For other surface preparation instructions, please visit the technical page on www.. APPLICATION: Step 1: Surface should be dry, clean and free of oil, wax, dirt, loose paint and other contaminants. Step 2: After entire surface is completely dry, properly ventilate room by opening windows, doors, turning on ceiling fans, etc. Step 3: Tape off application area with painter’s tape. Step 4: Mix contents of can well by shaking until the ball rattles within the can. Once ball rattles, continue to shake vigorously for 2-3 minutes. During use, shake intermittently for 10 seconds to keep product mixed. Step 5: Use painter’s paper to protect surround-ing areas from overspray. (Figure B)Spray 6 - 12 inches away from surface in a sweeping motion during application. Applying 2-3 light coats will cure, protect and look better than one heavy coat. Step 6: If spray stops or is irregular, turn can upside down and spray for 2-3 seconds to clear nozzle. Wipe tip, shake can and resume. Step 7: Slowly remove all tape and paper shortly after application. Allow 24 hours before use to allow product to fully cure. If product will be subject to prolonged periods of soaking in water, allow 48 hours before use to fully cure. CLEAN UP AND REMOVAL: • Remove overspray with paint thinner or lacquer thinner. • IMPORTANT: Before storing partial can, clean valve immediately after use. To clean, hold can upside down and spray until only clear gas comes out (approximately 3 - 5 seconds), then wipe tip and store. • If spray valve becomes clogged, pull off and clean in lacquer thinner. Replace spray valve pointing opening away from body. • If desired to remove product, use acetone. For more details, refer to the Non-Slip Spray Clear and White Technical Data Sheet.

Wood Guard Anti Slip Coating for Wood, Decks, Stairs, Patios and

Anti Slip Spray for Showers and Bathtubs - Fast Acting Non Slip

This easy to apply aerosol spray will create a clear non-skid surface will work on virtually any surface. You no longer have to worry about slipping and slipping in the bathtub shower boats etc. After one spray you will have a long lasting non slip solution.

Slip Doctors Anti-Slip Spray for Increased Grip on Fiberglass Acrylic Concrete and Tiles Clear Non-Slip Coating for Shower Bathtubs & Floors

Stone Grip (Gallon) Non-Slip Floor Treatment for Tile and Stone

Mainstream 60in x 32in 6-Jet Drop-In Whirlpool Tub

SlipDoctors Tub Grip Anti-Slip Bath & Shower Floor

Tub Guard Anti Slip Non Slip Bathtub and Shower Coating - White,2 oz - Innovative Tub Solutions

How to Fix a Slippery Bathtub

Cleaning the permanent slip-guard dots in my porcelain bathtub